Our News & Events

Home / News
AirTAC TCM25x20S – Three-Shaft Guided Pneumatic Cylinder Slide Bearing Bore 25mm Stroke 20mm Genuine

AirTAC TCM25x20S – Three-Shaft Guided Pneumatic Cylinder Slide Bearing Bore 25mm Stroke 20mm Genuine

Events, Article & Sharing      19/11/2026

AirTAC TCM25x20S – Three-Shaft Guided Pneumatic Cylinder Bore 25 × Stroke 20mm

Looking for a high-rigidity 25mm bore three-shaft guided pneumatic cylinder with a 20mm stroke engineered to withstand lateral side loads and prevent rod rotation? The AirTAC TCM25x20S belongs to the TCM guided cylinder series by AirTAC (dimensionally equivalent to SMC MGPM25-20Z). It features a 25mm bore, 20mm stroke, double-acting operation, wear-resistant bronze slide bearings, and a standard integrated magnet (S).

Key Features of AirTAC TCM25x20S

✅ Three-shaft guided pneumatic cylinder with rigid front tooling plate (TCM series – equivalent to SMC MGPM25-20Z).

✅ Bore: 25 mm (delivers strong linear thrust in a compact, rigid block).

✅ Stroke: 20 mm.

✅ Action: Double acting.

✅ Built-in magnet (S) included as standard for magnetic position sensor mounting.

✅ Dual 12mm guide shafts running in precision bronze slide bearings provide superior resistance to off-center loads, bending moments, and angular rotation.

✅ Multiple mounting faces (top, bottom, and rear) with precision dowel pin holes enable versatile multi-axis installation.

✅ Dual-end rubber bumpers absorb end-of-stroke impact and require no additional air line lubrication.

Technical Specifications

✅ Model: TCM25x20S (TCM25X20S)

✅ Series: TCM (Three-Shaft Guided Cylinder – Slide Bearing Type)

✅ Bore: 25 mm

✅ Stroke: 20 mm

✅ Main piston rod diameter: 10 mm

✅ Guide shaft diameter: 12 mm (bronze slide bearing)

✅ Action: Double acting

✅ Cushioning: Rubber bumper pads at both ends

✅ Magnet: Yes (S – standard)

✅ Operating pressure range: 0.15 – 1.0 MPa (22 ~ 145 psi)

✅ Proof pressure: 1.5 MPa (215 psi)

✅ Piston speed: 30 – 500 mm/s

✅ Operating temperature: -20°C ~ +70°C

✅ Port size: PT 1/8" (top and rear piping ports available)

✅ Fluid: Air (filtered by 40μm filter element)

Typical Applications

✅ Conveyor stopper mechanisms, off-center lifting stages, and heavy product diverting gates

✅ Packaging, filling, labeling, electronics assembly, and general factory automation lines

✅ Press-fitting jigs and workpiece clamping fixtures subjected to lateral side loads

✅ Direct drop-in dimensional and functional replacement for SMC MGPM25-20Z three-shaft cylinders

Why Choose the AirTAC TCM25x20S?

The AirTAC TCM25x20S combines pneumatic actuation and twin bronze-bushed guide shafts inside a single monolithic aluminum body, eliminating rod deflection and rotation under side loads. Multi-face mounting options and standard magnetic sensor slots make it a versatile workhorse for industrial automation.

Selection & Installation Tips

✅ Confirm 25mm bore, 20mm stroke, bronze slide bearings (TCM), and magnetic piston (S) match your side-load requirements (select AirTAC TCL25x20S if ball-bushing guidance for higher speeds is preferred).

✅ Verify that applied lateral loads and bending moments stay within TCM25 catalog ratings at a 20mm stroke.

✅ Supply clean compressed air filtered to 40μm or finer and install speed controllers on both PT 1/8" ports for smooth travel.

✅ Mount compatible magnetic sensors (such as CMSG or DMSG series) into the integrated body slots for stroke-end sensing.

Hotline: 0084 787900099

Social Share

Related Posts

hotline
Working hours: 9:00 - 18:00 (Excluding Saturday and Sunday)
©T Solution industry Vietnam Co., LTD2026. Login